Questions & Answers

2008 Toyota Yaris without transponder

0 votes

Hi guys. As you can see, I am trying to install an EVO ONE with KIT RFK411. I already have all the installation done but I have not been able to carry out the programming since this car does not have a TRANSPONDER. I am using this schematic: evo-one_ig_reg_bi_toy-yaris_2006_wokl_a_104141.pdf

Can you tell me what I should modify in the firmware, what programming should I do and what do I do with the TRANSPONDER connections? Thank you very much in advance.
 

 

posté Oct 3, 2022 dans la catégorie Toyota par Munito (1,500 points)

1 Réponse

+1 vote
 
Meilleure réponse
The vehicle must be automatic transmission.

 

Then youl would simply turn on 20.2 in the remote starter.

 

program your rf kit https://fortin.ca/download/68771/rfk411-install-guide-68771.pdf

 

at that point it should work since everything is a hard wired connection in this vehicle and it has no chip in the key.
répondu Oct 3, 2022 par derek g (340,240 points)
élue Oct 7, 2022 par Munito
Yes, I know how to programm the rf kit. I mean, what programation I have to use for the EVO ONE? Or just I have to ignore the programation in the EVO ONE and ignore the TRANPONDER conection as well? Just I have to modify the option 20.2 and proced with the RF programation, right?
commenté Oct 3, 2022 par Munito (1,500 points)
modifié Oct 3, 2022 par Munito
load any firmware you want into the bypass.

 

"Just I have to modify the option 20.2 and proced with the RF programation, right?"

 

- correct
commenté Oct 3, 2022 par derek g (340,240 points)
Hi Derek. Almost its done. I did that exactly you told me but now check this video 20 second video.

https://drive.google.com/file/d/11gLvQ-s6wbyjtXCu89yyfsO6FOemeuZ4/view?usp=sharing

Could it be a problem with the starter motor now? I already increased the crank time and with the key it starts correctly although sometimes it feels a bit heavy to start. What do you think?
commenté Oct 4, 2022 par Munito (1,500 points)
Verify you have powered the ignition switch properly.

 

If it still just cranks I would think the vehicle has a transponder in that case.
commenté Oct 5, 2022 par derek g (340,240 points)
I am going to check one more time but I think all the wiring it's correct. If it's has Transponder, where is it? Cuz near the ignition switch isn't.
commenté Oct 5, 2022 par Munito (1,500 points)
verify you are powering 2 ignitions and 1 starter wire.
commenté Oct 5, 2022 par derek g (340,240 points)
Hi Derek the order of the ignition matter? Look what I found. I think that I found the mistake. What do you think? Compare the original scheme with this picture.

https://ibb.co/QKk8tzf
commenté Oct 5, 2022 par Munito (1,500 points)
yes the order matters.

 

be sure you power the 2 ignitions and the starter or the vehicle may not remote start.
commenté Oct 5, 2022 par derek g (340,240 points)
Then you must to correct the scheme. I am going to connect the ignition wires in the correct order and I will let you know Friday afternoon.
commenté Oct 5, 2022 par Munito (1,500 points)
Also please ensure option 2.4 is on

 

https://fortin.ca/download/79141/evo-one_ig_reg_bi_toyota-yaris_2006-2010_a_79141.pdf
commenté Oct 6, 2022 par derek g (340,240 points)

Done! Thanks you very much Derek, excellent support from you and the person who emailed me anonymously. Again thank you very much. 

 
PD: Now you can close this post.
commenté Oct 7, 2022 par Munito (1,500 points)
modifié Oct 26, 2022 par Munito
Thank you and happy that you got it going.

 

Best Regards.
commenté Oct 27, 2022 par derek g (340,240 points)

Questions associées:

...